15DecDecember 15, 2025

ESP32 with 1.8″ TFT LCD Display (ST7735S)

🔧 1. Hardware Overview: 1.8" TFT DisplayMost 1.8" TFT modules are based on the ST7735 driver and communicate using the SPI (Serial Peripheral Interface) protocol.📦 Key Features:Resolution: 128×160 pixelsInterface: SPIColor depth: 16-bit (65K colors)Driver IC: ST7735 / ST7735SOperating voltage: 3.3V logic level (some have onboard regulators for 5V compatibility)Pins:VCC: Power (3.3V or 5V depending on module)GND: GroundSCL/SCK: SPI ClockSDA/MOSI: SPI DataRES/RST: ResetDC/A0: Data/Command selectorCS: Chip Select🔌 2. Wiring TFT to ESP32Assuming the display uses SPI and ESP32's VSPI (default) pins:TFT DisplayESP32 PinVCC5VGNDGNDSCL (CLK)GPIO 18SDA (MOSI)GPIO 23RESGPIO 15DCGPIO 32CSGPIO 5✅ Always check your specific...

IoT0 CommentsLike: 0

15DecDecember 15, 2025

ESP32 with BMP180 Pressure & Temperature Sensor

BMP180 Sensor: Digital Barometric Pressure SensorThe BMP180 is a digital barometric pressure sensor developed by Bosch Sensortec. It is commonly used in weather stations, altimeters, and GPS navigation systems. It can measure atmospheric pressure, temperature, and estimate altitude.🔧 Key FeaturesFeatureDescriptionPressure Range300 to 1100 hPa (hectopascal)Temperature Range0 to 65°CAltitude Resolution~0.17 metersInterfaceI²C (default), also supports SPISupply Voltage1.8V to 3.6VLow PowerIdeal for battery-operated devicesSizeVery compact (3.6 x 3.8 x 0.93 mm package)🧠 How It Works1. Pressure MeasurementThe sensor has a piezo-resistive element which changes resistance with pressure.A built-in ADC (analog-to-digital converter) digitizes this analog signal.Compensation algorithms (from...

IoT0 CommentsLike: 0

15DecDecember 15, 2025

Smart Display Interface Using SSD1306 OLED & ESP32

The SSD1306 is a popular controller used in OLED (Organic Light Emitting Diode) displays, most commonly found in small monochrome displays like 128x64 or 128x32 resolution screens. These displays are perfect for small embedded projects like IoT dashboards, sensor readouts, clocks, etc.📦 1. What is SSD1306?SSD1306 is a display driver IC developed by Solomon Systech.It controls monochrome OLED panels using I²C or SPI communication.Often embedded in 0.96-inch or 1.3-inch OLED displays.📐 2. Common SpecificationsFeatureDescriptionResolution128x64 or 128x32 pixelsDisplay TypeMonochrome OLED (white/blue/yellow)InterfaceI²C (2-wire) or SPI (4-wire)Voltage3.3V to 5V (check module)Power ConsumptionVery low (great for battery use)Color1-bit (pixel on or off)Size (Popular)0.96" diagonal🧪...

IoT0 CommentsLike: 0

15DecDecember 15, 2025

ESP32-Based Autonomous Fire Extinguisher Bot

🔥 FIRE BOT – Bluetooth Controlled Fire Extinguisher RobotWelcome to the FIRE BOT project! This robot is designed to detect and extinguish small fires using a flame sensor and a water pump. It is fully controllable via Bluetooth, making it ideal for educational or experimental firefighting applications.🧠 Features🔥 Flame detection💧 Water pump activation🎮 Bluetooth remote control (with mobile app)🛞 Motor movement: Forward, Reverse, Left, Right🔁 Servo motor to aim the water spray🧪 Manual + Automatic mode supported📦 Hardware UsedArduino Uno (or compatible...

IoT0 CommentsLike: 0

12DecDecember 12, 2025

ESP32 with DHT11 Temperature & Humidity Sensor

📌 What is the DHT11 Sensor?The DHT11 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and outputs a digital signal on the data pin (no analog input needed).🧠 Key Features of DHT11FeatureDetailsTemperature Range0 to 50°C (±2°C accuracy)Humidity Range20% to 90% RH (±5% accuracy)Operating Voltage3V to 5.5VSignal TypeDigital (single-wire serial)Sampling Rate1 Hz (one reading per second)SizeSmall and lightweight⚙️ Pinout of DHT11 SensorPinNameDescription1VCCPower supply (3.3V or 5V)2DataSerial data output3NCNot connected4GNDGround(Sometimes it comes in a 3-pin module: VCC,...

IoT0 CommentsLike: 0